167.net必赢(中国)官方网站·App Store

Philips Green Power
CDM-TP Lamps
Ideal for green houses,
growth chambers, and other
horticulture applications
Green Power CDM
An efficient growth light lamp
Philips Green Power CDM-TP Lamps provide outstanding growth
light performance and substantial energy savings when combined
with an efficient ballast.
Superior performance
&﹟8226; Excellent PPF (Photosynthetic Photon Flux) – 1.9 umols/s
&﹟8226; Superior lumen/PPF maintenance of 90% at 8,000 hours
&﹟8226; Long life – 20,000-hour rated average life&﹟8224;
&﹟8226; Suitable for use in open fixtures
Reduced cost of ownership
&﹟8226; Higher growth light compared to 400W HPS lamps*
&﹟8226; 93% ballast efficiency can provide substantial energy savings
&﹟8226; Increased time between re-lamping cycles when compared
to standard metal halide lamps**
(&﹟8224;, *, ** See back page for footnotes)© 2012 Philips Lighting Company. A Division of
Philips Electronics North America Corporation.
All rights reserved.
Printed in USA 6/12
P-6414
*域名隐藏*
Philips Lighting Company
200 Franklin Square Drive
Somerset, NJ 08873
1-800-555-0050
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics Ltd.
Philips Green Power CDM-TP Lamps
1) Measured at 100 hours of life in a vertical operating position. Measured at rated lamp watts on electronic ballast. Lumens per watt does not include ballast losses.
2) Approximate lumen output at 40% of lamp rated average life.
3) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least
50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average
Footnotes from front:
&﹟8224; Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least 50%
of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average
* When comparing Philips 400W HPS lamp PPF value (1.7) with Green Power CDM-TP Lamp PPF value (1.9).
** Point at which 10% failure point for standard 400W metal halide is approximately 9000 hours compared to 12,000 hours for Green Power CDM-TP Lamp.
Ordering, Electrical and Technical Data (Subject to change without notice)
Approx. Approx. Color Rated
Product Nom. ANSI Initial Mean Efficacy Temp. Burn Avg. Life PPF
Number Ordering Code Watts Code Lumens1 Lumens2 (lm/w) (Kelvin) CRI Position (Hrs.)3 (umol/sec)
41521-6 Green Power CDM-TP 315 C182/O 33,000 29,700 104 3200 90 Universal 20,000 1.9
315W/T12/U/O
WARNINgS, CAuTIONS,AND OPERATINg
INSTRuCTIONS FOR MASTERCOLOR CDM
ELITE MEDIuM WATT CERAMIC METAL HALIDE
AND gREEN POWER CDM-TP LAMPS
R“WARNIN in&﹟64258;ammation from short wave ultraviolet radiation if outer envelope g: These lamps can cause serious skin burn and eye
of the lamp is broken or punctured. Do not use where people will
remain for more than a few minutes unless adequate shielding or other
safety precautions are used. Certain lamps that will automatically extinguish when the outer envelope is broken or punctured are commercially
available.” This lamp complies with FDA radiation performance standard
21 CFR subchapter J. (USA:21CFR 1040.30 Canada:SOR/DORS/80-381
If the outer bulb is broken or punctured, turn off at once and
replace the lamp to avoid possible injury from hazardous
short wave ultraviolet radiation. Do not scratch the outer
bulb or subject it to pressure as this could cause the outer
bulb to crack or shatter. A partial vacuum in the outer bulb
may cause glass to &﹟64258;y if the envelope is struck.
WARNINg: The arc-tube of metal halide lamps are designed to operate under high pressure and at temperatures up to 1000º C and can
unexpectedly rupture due to internal or external factors such as a ballast
failure or misapplication If the arc-tube ruptures for any reason, the outer
bulb may break and pieces of extremely hot glass might be discharged
into the surrounding environment. If such a rupture were to happen,
THERE IS A RISK OF PERSONAL INJuRY, PROPERTY
DAMAgE, BuRNS AND FIRE.
RELAMP FIXTuRES AT OR BEFORE THE END OF RATED
LIFE. Allowing lamps to operate until they fail is not advised
and may increase the possibility of inner arc tube rupture.
This lamp contains an arc tube with a flling gas containing
Kr-85 and is distributed by Philips Lighting Company, a
division of Philips Electronics North America Corporation,
Somerset, New Jersey, 08873.
CAuTION: TO REDUCE THE RISK OF PERSONAL INJURY,
PROPERTY DAMAGE, BURNS AND FIRE RESULTING FROM AN
ARC-TUBE RUPTURE THE FOLLOWING LAMP OPERATINg
INSTRuCTIONS MUST BE FOLLOWED:
LAMP OPERATINg INSTRuCTIONS:
1. Relamp fxtures at or before the end of rated life. Allowing lamps to
operate until they fail is not advised and may increase the possibility
of inner arc tube rupture.
2. If the lamp is marked on the base with /E, use only in enclosed fxture
capable of withstanding particles of glass having temperatures up to
1000°C. If the lamp is marked on the base with /O, lamp should retain
all the glass particles should inner arc tube rupture occur.
3. Before lamp installation/replacement, shut power off and allow lamp
and fxture to cool to avoid electrical shock and potential burn hazards.
4. Use only auxiliary equipment meeting Philips and/or ANSI standards.
Use within voltage limits recommended by ballast manufacturer:
A. Operate lamp only within specifed limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
C. All Pulse Start lamps require a socket rated to withstand a 4,000
volt pulse
5. Periodically inspect the outer envelope. Replace any lamps that